15-5 is a variant of the older 17-4 chromium-nickel-copper precipitation hardening stainless steel. Both alloys exhibit high strength and moderate corrosion resistance. High strength is maintained to approximately 600 degrees F. The 15-5 alloy was designed to have greater toughness than 17-4. This improved toughness is achieved by reduced delta
AH36, DH36, EH36 Steel Plate for Shipbuilding. Shipbuilding steel plate refers to the carbon and alloy steel plate used in offshore and marine contructions, common grades are A, B, D, E, AH32/36/40, DH32/36/40, and EH32/36/40 which ranged from different strength. The plates usually used to manufacture ship hulls, bulkheads, upper decks and ASSAB Tool Steel Performance Comparison ChartASSAB XW-5 SVERKER 3 D6 (D3) (1.2436) (SKD 2) HB 240 2.05 0.3 0.8 12.7 -1.1 920-1000 56-62 A 12% Cr, high carbon tool steel with excellent abrasive wear resistance. Blanking, punching, cropping, shearing, trimming and clipping.
COVERING CAST AND EQUIVALENT FORGED VALVES Important Note:Data provided on this chart is for information purposes only. Always consult current ASME or API official publications to verify information and cross reference data. ASTM A216/A352 permits maximum carbon content of 0.30% for grade LCB/WCB but GSL only allows 0.25% maximum. Carbon Steel 1050 Rolled Metal Products Stainless Rolled Metal Products is one of the steel industrys most respected service centers with facilities across North America. We stock Stainless Steel, Nickel Alloys, Aluminum and other Specialty Metals in coil form and also offer toll processing of various metals including:Stainless Steel, Nickel Alloys, ium, Aluminum, Brass, Copper, Carbon Steel, and other Specialty Metals.
Related Topics . Codes and Standards - Piping codes and standards - ASME, ANSI, ASTM, AGA, API, AWWA, BS, ISO, DIN and more..; Piping Systems - Dimensions of pipes and tubes, materials and capacities, pressure drop calculations and charts, insulation and heat loss diagrams; Related Documents . ASME/ANSI B36.10/19 - Carbon, Alloy and Stainless Steel Pipes - Dimensions - Metric Units - Pipe EN 1.0503 - Equivalent MaterialsThere are 31 equivalent materials for EN 1.0503 Carbon Steel. See the equivalents for ASTM, DIN, AFNOR, BS, UNI, SS, UNE, AISI, SAE, JIS, EN, ISO, GOST, GB, GB/T and UNS.
EN 1.0503 Material C45 Steel. EN 10083-2 C45 steel (EN 1.0503) is a high strength medium carbon quality steel. Due to poor hardenability, C45 material is generally used in a normalized condition, and when the mechanical properties are required to be high, EN 10088-3 Chemical Composition Stainless SteelEN 10088-3 Chemical Composition Stainless Steel. EN 10088-3 is the material standard for stainless steel semi-finished products, bars, rods and sections for general purposes. Ferritic, martensitic, precipitation hardening, austenitic and austenitic-ferritic duplex grades are included. The chemical composition of all the grades of stainless steel covered in the standard are listed.
S0.05 Color JIS equivalent Free-cutting elements added Original steel 8% Cr steel Original steel Original steel Original steel Original steel P/M high speed steel P/M high speed steel High-performance cold work tool steel 40HRC pre-hardened steel Cold work tool steels High speed tool steels P/M High speed tool steels Matrix high speed steel Low Alloy Molybdenum-Nickel Steels SSI Sintered SpecialtiesJapan steels are listed in JIS Z2550, with grade names changing with the revision from 1989 to 2000. Low alloy steel with prealloyed manganese, molybdenum and nickel content for better hardenability. Low alloy steel with prealloyed molybdenum and admixed nickel and copper for better compressibility.
Structural Steel St44-2 17100 1.0044 Thick. (25) A48 Gray Cast Iron Casings Class No. 25 F11701 GC200/FC200 D4301/G5501 - GG20 1691 0.6020 - A53 Welded and Seamless Steel Pipe Grade A K02504 SPPS38/STPG370 D3562/G3454 (16) St37.2 1626 1.0036 (18)Welded St35 1629 1.0308 (18)Seamless Grade B K03005 SPPS42/STPG410 D3562/G3454 (16) St45 1629 1.0408 Material Equivalent Standards - Neelcon SteelMaterial Equivalent Standards. equivalent standards table, equivalent standards steel. equivalent standards to iso 9001, equivalent standards astm, equivalent standards st52, material equivalent standards, asme equivalent standards, iso equivalent standards, We listed up our recommendations for you ! Neelcon Steel offers C45 Plate and more.
Stainless Chromic-Nickel Steel- Clad Plate, Sheet, and Strip G 3601 (2) 3740 (2) 17440/1 A-265 Nickel and Nickel-Base Alloy-Clad Steel Plate G 3602 (2) --- 17743 NiCu30Fe A-283 Low and Intermediate Tensile Strength Carbon Steel Plates, Shapes, and Bars Steel Grade Equivalency TableSteel Grade Equivalency. A633 Gr. A,C,D. 0.9 max. Comparative designations of grades with similar composition from other important standards. Unified Numbering System (UNS) is an alloy designation system widely accepted in North America. American Iron and Steel Institute (AISI) standards for steel compositions. European standards.
Steel Grade Equivalent Table (EN, SAE/AISI, UNS, DIN, BS, UNI, JIS) The table below compares common grades of materials from various international specifications. Note that materials compared are the nearest available grade and may have slight variations in actual chemistry. Steel standards - equivalence - MP MétalEquivalent qualities according to former national standards:Standard:Symbolic designation Former designation France NFA Germany DIN Italy UNI Great Britain BS USA ASTM Japan JIS 1. Uncoated mild steels for stamping:EN 10 130:36.401 (1983) 1623-1 (1983) 5866 (1977) 1449-P1 (1983) A 366-91 A 619-92 A 620-92 3141 (1990) DC 01 DC 03 DC 04 DC 05
Jul 24, 2010 · Table of Steel Equivalent Grades (EN, SAE/AISI, UNS, DIN, BS, UNI, JIS) The table below compares steel equivalent grades of materials from various international specifications. Note that materials compared are the nearest available grade and may have slight variations in actual chemistry.15CD2.05 (AFNOR NFA ) - Worldwide equivalent gradesWorldwide equivalents of grade 15CD2.05 (France:AFNOR NFA ) Steel :15CD2.05. France. Standard :NF A36-206. Cross reference table. for Steel 15CD2.05 (AFNOR NFA ) and its European equivalent 13CrMo4-5 (1.7335) ( EN ) EU. EN. USA.