Alloy E8740 is a triple alloy (Ni-Cr-Mo) produced in Electric Furnaces to Aircraft Quality. When quenched and tempered, it provides good hardenability, and resistance to shock. It is free from temper brittleness. 8740 is similar to alloy 8640 and is commonly used as its replacement for high strength fasteners.
This specification covers Ni-Fe-Cr-Mo-Cu-N low-carbon alloys (UNS N08925, UNS N08031, UNS N08354, and UNS N08926), Cr-Ni-Fe-N low-carbon alloy (UNS R20033) bar and wire, and Ni-Cr-Fe Mo-N alloy (UNS N08936) wire. The material shall be supplied in the solution-treated or in cold drawn condition as required. ASTM B649 - 17 Standard Specification for Ni-Fe-Cr-Mo-Cu This specification covers Ni-Fe-Cr-Mo-Cu-N low-carbon alloys (UNS N08925, UNS N08031, UNS N08354, and UNS N08926), Cr-Ni-Fe-N low-carbon alloy (UNS R20033) bar and wire, and Ni-Cr-Fe Mo-N alloy (UNS N08936) wire. The material shall be supplied in the solution-treated or in cold drawn condition as required.
Datasheet February 01 2021. ATI 35N:35Co-35Ni-20Cr-10Mo Alloy Alloy Cross Reference Coil elements, resistance wire 601 ~ 601 alloy :cr 20 cb 1 si 2 ni bal:crxds:crx ds :tophet d + cb :inacreep ds :242 ~ nicr 80 cb:alloy 242 :ni 35 cr 20 cb 1 fe bal:crxcb:crx cb :inacreep 40 cb :520 ~ nicr 35 cb:chromax 520 :cr 20 mo 10 ni 35 co bal:mp35n:mp35n :ni 34-37 cr 18-20 si 1-1.5 mn 2 cu 1 fe bal:ra330 :stainless 330 :inacreep 330 :ni 8-12 cr 18
601 ~ 601 alloy :cr 20 cb 1 si 2 ni bal:crxds:crx ds :tophet d + cb :inacreep ds :242 ~ nicr 80 cb:alloy 242 :ni 35 cr 20 cb 1 fe bal:crxcb:crx cb :inacreep 40 cb :520 ~ nicr 35 cb:chromax 520 :cr 20 mo 10 ni 35 co bal:mp35n:mp35n :ni 34-37 cr 18-20 si 1-1.5 mn 2 cu 1 fe bal:ra330 :stainless 330 :inacreep 330 :ni 8-12 cr 18 Crevice Corrosion Repassivation of Ni-Cr-Mo Alloys by Ni-Cr-Mo alloys offer outstanding corrosion resistance in hot chloride solutions. Crevice corrosion is the expected form of localized corrosion as pitting corrosion requires very harsh conditions to occur in Ni-Cr-Mo. Crevice corrosion may proceed only if specific conditions are met (e.g., temperature and potential should be above the critical values for each alloy).
(Alloy 218) (UNS S21800) Fe 63, Cr 17, Mn 8, Ni 8.5, Si 4, N 0.13 High strength fully Austenitic alloy that resists galling and wear. Significantly lower cost to extend part life and lower maintenance. The yield strength is twice that of 304 and 316 stainless steels, in the annealed condition. Tensile strengths can be produced in excess of 200 ksi. Lubrication behavior of NiCr-based alloys containing Oct 01, 2001 · NiCr-based alloys with excellent self-lubricating property in a wide temperature range were prepared by powder metallurgical hot pressing of alloyed NiCr powder, Mo, Al, Ti, B and various proportions of MoS 2 powder. The effects of MoS 2 on some mechanical and tribological properties of the alloys when rubbing with W18Cr4V high-speed steel were investigated in the temperature range of 20
Several Ni-Cr and Ni-Cr-Mo materials (for example HASTELLOY® C-4, C-22HS®, HYBRID-BC1®, Alloy 59, and G-35® alloys) are effectively ternary systems. All except C-4 alloy (which is well within the gamma phase field, and consequently relatively stable) are close to the gamma phase field boundary. Modeling of Ni-Cr-Mo based alloys:Part I-phase stability T1 - Modeling of Ni-Cr-Mo based alloys. T2 - Part I-phase stability. AU - Turchi, P. E.A. AU - Kaufman, L. AU - Liu, Zi Kui. PY - 2006/3/1. Y1 - 2006/3/1. N2 - The CALPHAD approach is applied to the study of the stability of several candidate Ni-Cr-Mo based alloys for use in waste disposal canisters for the Yucca Mountain Project (YMP).
Ni-Cr-Mo alloys for mixed environments; Ni-Cr-Plus alloys for elevated temperature applications Contact Us:2 Brands Hatch Close, Kyalami Business Park, Midrand +27 (0)11 466 2480 +27 (0)11 466 1692; [email protected]; Alloys. Copper Based Alloys Products ICD Alloys & Metals, LLCNi/Cr/Mo Alloys; Ni/Fe Alloys; Ni 200; PWA Alloys; Cobalt 58.933 CO
SAE-AISI 4340 (SNCM439, G43400) Ni-Cr-Mo Steel SAE-AISI 4340 steel is an alloy steel formulated for primary forming into wrought products. 4340 is the designation in UNS (Unified Number System) Cross - Unified AlloysCr-Ni-Cu-Mo Alloy N08021:Cr-Ni-Cu-Mo Alloy N08022:Cr-Ni-Fe-Mo-Cu Alloy N08024 *Carpenter 20Mo-6 N08026 *Sanicro 28 Austenitic N08028:Alloy 31 N08031 *INCO Alloy 032 N08032:20MO-6HS N08036:NIC 42M N08042 *ACI HT-50 N08050 *Incoloy FM65 N08065:SM 2035 N08135:46Fe-32Ni N08151:Ni-Fe-Cr-Cu
Nickel-molybdenum (Ni-Mo), nickel-molybdenum-chromium (Ni-Mo-Cr) alloys (Hastelloys):Alloys in this category are used for their high strength despite high temperatures and corrosive surroundings Ni/Cr/Mo Alloys ABCOM Pte LtdNI/CR/MO Alloys. The typical grades we offer on regular basis are:AL6XN. SMO 254. 904 L. SUPER DUPLEX. A286. Ni 80A. INVAR 36.